Regulations & Safety
EASA Proposes Take-Off Performance Monitoring Mandate by 2033
EASA Opinion No 07/2026 proposes mandatory take-off performance monitoring systems on new large commercial aircraft by 2033.

The European Union Aviation Safety Agency (EASA) has formally proposed mandating the installation of take-off performance monitoring systems on all newly produced large commercial aeroplanes by 2033.
Published on September 22, 2026, Opinion No 07/2026 recommends amending European Union regulations to mitigate the risk of runway excursions and aircraft upsets caused by incorrect data entry or erroneous take-off positions. The proposal follows an extensive analysis of historical incidents and targets a six-year implementation window after the rules enter into force.
Mitigating runway excursions and performance errors
The push for a Take-off Performance Monitoring System (TOPMS) addresses a persistent vulnerability in commercial aviation: incidents where incorrect data entry leads to degraded take-off performance. Common errors include entering the wrong aircraft weight, calculating incorrect reference speeds, or initiating the take-off roll from the wrong runway intersection.
According to data published by aviation outlet dlapilota.pl, EASA analyzed 118 events related to erroneous take-off parameters or aircraft positioning that occurred between 1998 and 2023. This dataset included 18 accidents, five of which were fatal. The agency estimates that the proposed TOPMS functions could have prevented 90% of these analyzed events.
The system is designed to monitor parameters and position before the take-off roll begins. For certain large transport aircraft, it will also monitor real-time acceleration and performance during the take-off roll itself, alerting crews if the aircraft is not achieving the required performance to safely become airborne.
The objective is to mitigate, using an on-board alerting system, the risk of large aeroplane accidents or incidents caused by the use of erroneous take-off performance parameters and erroneous take-off positions.
EASA noted in its regulatory filings that these specific errors have the potential to result in runway excursions and aeroplane upsets, which can lead to subsequent loss of control and collision with terrain or obstacles.
Implementation timeline and manufacturer impact
The mandate will apply exclusively to newly produced large aeroplanes used in commercial air transport. EASA explicitly stated that it does not propose mandatory retrofitting of previously produced aircraft. This decision limits the financial burden on current airline operators and focuses the regulatory effort on future production lines from manufacturers like Airbus and Boeing.
The compliance timeline requires the systems to be installed on newly produced aircraft six years after the implementing regulation enters into force. With the European Commission projected to adopt the amendments in 2027, the mandate will take effect in 2033.
The proposed regulatory material is intended to improve safety while limiting manufacturers’ efforts as regards the development and implementation of TOPMS functions to the most beneficial cases. A low-to-very-low cost impact is expected. No environmental and social impacts have been identified.
The regulatory path to Opinion No 07/2026
The publication of Opinion No 07/2026 marks the formal recommendation from EASA to the European Commission to amend Regulation (EU) 2015/640. The rulemaking process began on August 30, 2023, when EASA published the Terms of Reference for Rulemaking Task RMT.0741 to address take-off performance parameters and position errors.
Following nearly two years of development, EASA published a Notice of Proposed Amendment (NPA 2025-01) on July 1, 2025, opening the rules for public consultation. The September 22, 2026 publication includes the final Opinion alongside the Comment Response Document (CRD 2025-01), which addresses industry feedback received during the consultation period.
The European Commission is now tasked with reviewing and adopting the proposed amendments, a process expected to conclude in 2027.
AirPro News analysis
The decision by EASA to exclude legacy aircraft from the TOPMS mandate represents a pragmatic approach to aviation safety regulation. Retrofitting complex avionics and performance monitoring systems into older airframes is technically challenging and cost-prohibitive. By focusing entirely on newly produced aircraft, EASA ensures that the next generation of commercial aeroplanes will feature a critical safety net against human data-entry errors, without grounding or financially penalizing current fleets. We view this as a targeted strategy that prioritizes long-term safety architecture over immediate, disruptive mandates, giving original equipment manufacturers ample time to integrate these systems into their production lines by 2033.
Regulations & Safety
NTSB Urges Forest Service to Tighten Retardant Corrosion Testing
The NTSB issued two safety recommendations after significant corrosion was found on two airtankers used in a 2023 fire retardant evaluation.

The National Transportation Safety Board (NTSB) has issued two safety recommendations to the U.S. Forest Service after investigating significant corrosion found on two large airtankers that took part in a 2023 evaluation of a new fire retardant. The NTSB is calling on the agency to strengthen its corrosion testing requirements for aerial firefighting retardants.
In a press release dated November 17, 2026, the NTSB said existing testing requirements allowed a new fire retardant to receive full qualification without adequately evaluating its potential corrosive effects on aircraft materials and structures. The findings are set out in Aviation Investigation Report AIR-26-06, “Require Adequate Corrosion Testing and Qualification of Long-Term Fire Retardants Used in Aerial Firefighting,” adopted on November 2, 2026, under investigation DCA26SR006.
The two airtankers and the 2023 evaluation
According to the report, the investigation involved Tanker 02 (N474NA), a British Aerospace BAE-146-200A owned, operated and maintained by Neptune Aviation Services of Missoula, Montana, and Tanker 106 (N296EA), a McDonnell-Douglas DC-9-87 (MD-87) owned, operated and maintained by Aero Air of Hillsboro, Oregon.
Both aircraft took part in a Forest Service integration-operational field evaluation of Fortress FR-200, a liquid long-term retardant manufactured by Fortress North America with magnesium chloride as its active salt, the report states. In the first phase, from June 16 to August 13, 2023, the evaluation used FR-200 only. In the second phase, from August 14 to November 21, 2023, FR-200 was used alternately with MVP-Fx, an ammonium phosphate retardant manufactured by Perimeter Solutions and marketed under the Phos-Chek brand.
The report also describes a control airplane, Tanker 107, an Aero Air MD-87 (N297EA) that did not carry FR-200. In its release, the NTSB said comparable aircraft that had not carried the new retardant did not show corresponding corrosion.
What the inspections found
Operators documented corrosion and material deposits during the evaluation, according to the NTSB. The report states that on July 16, 2023, Neptune’s first tank entry on Tanker 02, after 64 drops, found gelatinous, black and crystallized deposits. On August 25, 2023, Aero Air found corrosion on both 40-inch flat-steel springs holding the negative-pressure vent doors of the aft upper tank on Tanker 106, and the report states that the right spring had fractured about 1 inch from its attachment.
Later inspections found extensive corrosion affecting aircraft structures and systems, including primary wing structure, fuselage components, electrical connectors, control cables and engines, the NTSB said. In January 2024, Aero Air’s detailed postseason inspection of Tanker 106 found intergranular corrosion in a lower-cap doubler on the right-wing forward spar, according to the report.
The Forest Service informed the NTSB of the postseason corrosion findings on March 11, 2024. An NTSB-led group examined Tanker 02 on March 13, 2024, and Tanker 106 on March 14, 2024, and samples were sent to the National Institute of Standards and Technology (NIST) in Boulder, Colorado, the report states.
According to the NTSB’s release, the report notes that, besides increased maintenance and repairs, chemical corrosion can “weaken aircraft structures and, if left undetected or uncorrected, lead to structural failure.”
How the retardant was qualified
The Forest Service qualifies long-term retardants under its Specification 5100-304d, Long-Term Retardant, Wildland Firefighting. According to the report, the agency replaced Specification 5100-304c with 5100-304d in January 2020, dropping the phosphate-only requirement. FR-200 received conditional qualification in August 2021 and full qualification in December 2022, when the Forest Service’s Qualified Products List showed it as fully qualified at a 2.4:1 mix ratio.
Investigators found that the Forest Service’s qualification process relied mainly on corrosion testing of isolated metal samples, the NTSB said. The process did not adequately account for the combinations of materials and structures found in aircraft, or for the potential effects of mixing chemically different retardants.
The Forest Service suspended the qualifications of the new retardant and a related product in May 2024 and removed both from its Qualified Products List in December 2024, according to the NTSB. The NTSB concluded that these actions did not address the underlying deficiencies in the qualification process.
Probable cause and the two recommendations
The NTSB’s investigation page for DCA26SR006 states the probable cause, using LTFR for long-term fire retardant:
The NTSB determined that the probable cause of this incident was the use of a new LTFR with a chemical composition incompatible with the retardant previously in use for the integration-operational field evaluation without adequate testing and qualification.
Both safety recommendations are addressed to the United States Forest Service:
- A-26-66 asks the Forest Service to work with aircraft corrosion experts from industry and government, airtanker operators and retardant manufacturers to develop corrosion test procedures that cover the range of aircraft materials, built-up structures, galvanic coupling, retardant comingling and possible chemical interaction effects.
- A-26-67 asks the Forest Service to revise the long-term retardant qualification requirements in Specification 5100-304d to incorporate the procedures developed in response to A-26-66.
In its release, the NTSB summarized the recommendations as asking the Forest Service to work with industry experts, airtanker operators and retardant manufacturers to develop more comprehensive corrosion testing procedures and to put them into its qualification requirements. The report, AIR-26-06, is published on the NTSB’s website with the investigation page for DCA26SR006.
Regulations & Safety
ICAO Convenes First Worldwide Air Transport Conference Since 2013
ICAO’s ATConf/7 runs November 16 to 20 in Montréal to rework aviation’s economic rules as traffic heads toward 12.4 billion passengers by 2050.

The International Civil Aviation Organization’s (ICAO) Seventh Worldwide Air Transport Conference (ATConf/7) runs from November 16 to 20, 2026, at ICAO Headquarters in Montréal, the first such conference since 2013. Its task is to produce recommendations on policy guidance and a harmonized regulatory framework for sustainable international air transport, with future actions for States and ICAO.
ICAO set out the stakes in an article published on its website on November 12, 2026, under the byline of ICAO Council President Toshiyuki Onuma: “A new global economic framework will define the next era of international air transport.” Onuma wrote that the rules and systems that once sustained aviation’s growth “must once again adapt to build a resilient, sustainable, and inclusive future.”
What ICAO says the economic rules must now absorb
Onuma’s article lists the shocks since the last conference. The COVID-19 pandemic, which he called aviation’s most serious crisis, erased demand and created intense financial stress, and the system has since faced geopolitical tensions, airspace disruptions, energy volatility and global macroeconomic uncertainty.
He named the persistent challenges ICAO wants the conference to address: infrastructure constraints, the modernization of economic regulatory frameworks, chronic supply-chain disruptions and tightening financing conditions, as well as cybersecurity, data governance, workforce skills and, “above all, the climate emergency.” Negotiations at ICAO, he wrote, are needed to ensure the commercial viability of emerging technologies and operational models and to establish the certainty needed for long-term investment.
With passenger numbers projected to reach approximately 12.4 billion by 2050, Onuma wrote that existing systems must give way to new regulatory and economic frameworks. The conference coincides with the launch of ICAO’s Strategic Plan for 2050, which envisions “air transport for all” while aiming for zero fatalities and net-zero carbon emissions. He called the meeting “a singular opportunity for delegates to re-engineer the economics of aviation.”
Six objectives and four agenda items
The ICAO Council gave the conference six objectives, according to the Secretariat’s working paper ATConf/7-WP/1, under the theme “Air Transport: Powering Global Connectivity, Economic Development and Resilience in a Dynamic World”:
- Advance economic regulatory frameworks that adapt to market trends and technology, using data.
- Improve industry resilience on workforce, supply chains, market access, emergency response and consumer protection.
- Mobilize blended financing for civil aviation infrastructure.
- Shape economic policy foundations for innovation and emerging technologies.
- Strengthen institutional and human capacity.
- Enable sustainable and inclusive air transport growth.
The agenda turns those objectives into four items. The first reviews developments since ATConf/6, including the effects of COVID-19, and the place of air transport in ICAO’s Strategic Plan 2026-2050. The second covers investment in infrastructure, people and partnerships, including financing for advanced air mobility (AAM) and AI-enabled systems with multilateral financial institutions.
The third item deals with regulatory and institutional frameworks: market access, liberalization, market concentration and fair competition; emergency planning and consumer protection, including assistance to passengers and accident victims under the Montreal Convention 1999; and, under Agenda Item 3.4, levies on international air transport, including possible cost recovery for unmanned aircraft systems (UAS) and new entrants. The fourth covers the economic regulation of AAM, artificial intelligence, suborbital and commercial space transport, access to sustainable aviation fuel (SAF) and lower carbon aviation fuels (LCAF), and air transport data and cybersecurity.
A policy forum that meets about once a decade
ATConf/7 builds on ATConf/4 in 1994, ATConf/5 in 2003 and ATConf/6 in 2013, according to WP/1. Onuma wrote that the last conference produced economic policy recommendations that prepared the sector for one of its most challenging eras, and that the ICAO Long-Term Vision for International Air Transport Liberalization adopted there is driving the creation of new markets for air services in emerging economies.
ICAO Secretary General Juan Carlos Salazar urged States to prepare for the November conference at a meeting of Directors General of Civil Aviation in Puglia, Italy, that ended on June 11, 2026. ICAO said these conferences occur about once a decade and set the global policy agenda for the economic regulation of international aviation. Onuma called for regional input to the global policy framework at the 61st Asia-Pacific directors general conference in September 2026.
WP/1 frames the economic weight of the sector the delegates are discussing: a direct contribution estimated at USD 4.1 trillion, equivalent to 3.9 percent of world gross domestic product, 86.5 million jobs, 4.6 billion passengers in 2024, and goods transported by air valued at USD 8 trillion.
What airlines have put on the table
The International Air Transport Association (IATA), an official observer at ICAO, says it submitted eight working papers, two of them jointly with Airports Council International (ACI) and two as information papers. In WP.23, IATA asks that economic regulation be proportionate, responsive and evidence-based, and that ICAO develop a Good Regulatory Practices toolkit that includes cost-benefit analysis and impact assessment.
On infrastructure costs, WP.25 calls for stronger implementation of ICAO’s charging principles of cost-relatedness, transparency and consultation, scrutiny of infrastructure investment, and independent economic oversight of airports and air navigation providers. On consumer protection, WP.24 proposes that ICAO create a standardized Air Passenger Handbook and asks governments to protect the commercial and pricing freedoms that let airlines offer varied products and fares.
On the environment, WP.30 argues that scaling SAF needs coordinated, sequenced government policies on supply, infrastructure and investment, not mandates alone, and WP.31 asks governments to reinforce the Carbon Offsetting and Reduction Scheme for International Aviation (CORSIA) as the single global market-based mechanism and to avoid overlapping measures. A joint IATA and ACI paper, WP.65, asks that a UN Framework Convention on International Tax Cooperation respect ICAO’s aviation taxation framework.
What happens before the week ends
WP/1 schedules the formal opening for Monday, November 16, followed by the election of the Chair and Vice-Chairs, a high-level panel and the first sessions on Agenda Item 1. The tentative timetable then gives one day to each remaining agenda item and schedules approval of the conference report and adoption of a Ministerial Declaration on the final day, November 20.
The 43rd (Extraordinary) Session of the ICAO Assembly meets alongside the conference on November 19 and 20, 2026. The Assembly, ICAO’s sovereign body, is normally convened by the Council every three years; its last regular session was the 42nd Assembly in 2025. After a Protocol amending the Convention on International Civil Aviation, signed in Montréal on October 6, 2016, entered into force, Council membership grew from 36 to 40 Contracting States, and this session will elect four additional Council Members, according to ICAO’s Uniting Aviation.
Regulations & Safety
FAA Proposes Ending Paper Payments for Registration Fees and Penalties
The FAA proposes electronic-only payment for aircraft registration and recording fees, certificates and civil penalties. Comments due Jan. 4, 2027.

The FAA has proposed to stop accepting cash, money orders and paper checks for aircraft registration and recording fees, replacement airman and medical certificates, overflight fees and civil penalties, and to require electronic payment instead. Comments on the proposal are due by January 4, 2027.
The agency published the notice of proposed rulemaking (NPRM), titled “Modernizing to Electronic Payments,” in the Federal Register on November 17, 2026, under Docket No. FAA-2026-3538 (Notice No. 27-01, Regulation Identifier Number 2120-AM16). The FAA said the proposal complies with Executive Order 14247, “Modernizing Payments To and From America’s Bank Account,” which seeks to phase out paper receipts and require electronic payments to and from federal agencies.
What would change for registrants, pilots and lessors
The proposal amends payment provisions in Title 14 of the Code of Federal Regulations (14 CFR) parts 13, 47, 49, 61, 63, 65, 187 and 406. According to the NPRM, those provisions cover aviation and commercial space transportation civil penalties, aircraft registration fees, fees for aircraft recording, duplicate airmen and medical certificates, duplicate knowledge test reports, overflight fees and FAA services performed outside the United States.
Sections 47.17, 49.15, 61.29, 63.16, 65.16 and 406.9 currently list only paper payment methods. Section 47.17(b), for example, requires applications for aircraft registration services, including dealer certificates, special registration numbers and registration renewals, to be accompanied by a check or money order. The FAA proposes to replace “check and money order” with “electronic payment.” The FAA Registry already accepts electronic payments for these services through its Civil Aircraft Registry Electronic Services (CARES) portal and Pay.gov, the NPRM says.
Under part 49, the FAA collects fees for recording conveyances of aircraft, aircraft engines and propellers. The proposal would require electronic payment for those recording fees as well. For replacement airman certificates, medical certificates and knowledge test reports under section 61.29, paper payment would be removed, although requests for a replacement airman certificate could still be mailed in.
The FAA also proposes housekeeping changes in part 61: updating the medical certification post office box from 26200 to 25082 because the address has changed, and pointing the Airmen Services web address directly to amsrvs.registry.faa.gov/amsrvs. For civil penalties under sections 13.15, 13.16 and 13.18, options to pay by certified check, money order or other paper methods would be removed.
Each change would apply unless another payment method is otherwise authorized by law. The FAA also plans to revise guidance documents, including Advisory Circular (AC) Form 8050-1B, AC Form 8050-5 and AC Form 8060-56, to remove references to paper payment, and will post drafts to the docket for comment.
Bringing the rules in line with practice
The FAA says the regulatory text diverges from its current practice. The agency already asks customers to pay the fees and penalties covered by the proposal through Pay.gov, the U.S. Treasury Department’s website, and accepts electronic payments for several fees even though the rules do not mention them.
According to the NPRM, the regulations have been amended only twice since 1997 to accept electronic payments. The FAA began accepting electronic payments in 1997 for air traffic services for certain flights through the National Airspace System (NAS), by amending section 187.15(d). It amended the rules to allow credit card payment for certification services performed outside the United States in 2007, and to accept electronic payments for civil penalties in 2021.
The executive order behind the proposal was signed on March 25, 2025. It directed the Treasury Secretary to stop issuing paper checks for federal disbursements from September 30, 2025, and required payments to the government to be processed electronically as soon as practicable, with limited exceptions. The order said Treasury checks are 16 times more likely than an electronic funds transfer to be reported lost or stolen, returned undeliverable or altered. AirPro News previously covered the switch to electronic registration certificates, an earlier step away from paper at the FAA Registry.
Costs and savings
The FAA estimates the rule would save the agency $99,815 a year by ending the processing of paper payments. Over five years, it puts the savings at $457,125 at a three percent discount rate or $409,262 at seven percent, and at $1,425,933 in perpetuity. The agency expects the cost to customers of moving from paper to electronic payment to be de minimis.
Comments can be submitted under docket number FAA-2026-3538 through the Federal eRulemaking Portal at regulations.gov, by mail, by hand delivery or by fax. The FAA contact for the rulemaking is Sierra Elam of the Office of Rulemaking.
-
Commercial Aviation7 days agoLufthansa A350-1000 Brings Starlink Wi-Fi to Long-Haul on December 3
-
Space & Satellites4 days agoNASA Targets November 18 Undocking for SpaceX CRS-35 Cargo Dragon
-
Company Performance5 days agoS&P Upgrades Aviation Capital Group to BBB After ITOCHU Deal Closes
-
Space & Satellites4 days agoSierra Space Expands Victory Works Satellite Factory in Colorado
-
Route Development3 days agoPhoenix Sky Harbor Unveils Preferred West Terminal Concept
