Regulations & Safety
Jet2 Contractor Seriously Injured After Fall at Manchester Airport
A contractor fell from a Jet2 plane at Manchester Airport, sustaining serious injuries. Jet2 is conducting a full investigation into the incident.

This article summarizes reporting by Manchester Evening News and Paul Britton.
A severe incident at Manchester Airport on Saturday morning left an aviation contractor with serious injuries after falling from a Jet2 aircraft. Emergency responders were dispatched to the tarmac following the fall, which occurred near the rear of the plane.
According to reporting by the Manchester Evening News, the injured individual is believed to be an aircraft engineer employed by a third-party provider. The worker sustained multiple severe injuries, including fractures to the arm and leg, and was transported to a local hospital for ongoing treatment.
The aircraft involved was reportedly preparing for a scheduled departure to Tenerife when the fall occurred at approximately 8:00 a.m. local time. Jet2 has since confirmed that a comprehensive investigation into the workplace accident is underway.
Emergency Response on the Tarmac
Immediate Medical Attention
Following the fall, paramedics from the North West Ambulance Service were immediately scrambled to the scene to provide critical care. Witnesses cited by the Manchester Evening News noted that emergency personnel erected medical screens around the injured contractor while administering first aid on the tarmac.
The prompt response highlights the severe nature of the injuries sustained. The worker, whose identity has not been publicly released, remains hospitalized as medical teams address the significant bone fractures resulting from the drop.
Aircraft and Equipment Positioning
Photographs and witness accounts from the scene indicate that the Jet2 aircraft had a rear door open near the tail section at the time of the accident. Mobile passenger stairs were also observed in close proximity to the aircraft.
While the exact sequence of events leading to the fall remains unconfirmed, the positioning of the open door and the mobile stairs will likely be a focal point for safety investigators examining how the contractor fell from the elevated threshold.
Jet2 Launches Full Investigation
Airline Acknowledges Third-Party Involvement
In the wake of the accident, Jet2 issued a public statement acknowledging the event and clarifying the worker’s employment status. The airline noted that the individual was not a direct employee but worked for an external service provider contracted at the airport.
In a statement provided to the press, a Jet2 spokesperson confirmed the ongoing inquiry:
“We are unable to confirm further details at present, however, can confirm that a full investigation has been launched.”
The airline also emphasized that they are working to provide necessary support to those affected by the morning’s events.
AirPro News analysis
Ground handling and aircraft maintenance are inherently high-risk environments, particularly when personnel are operating near open cabin doors or elevated service platforms. Standard operating procedures typically dictate strict protocols for the placement and removal of mobile stairs, as well as the securing of aircraft doors when ground equipment is not flush against the fuselage.
When a worker falls from an aircraft door, investigators usually examine whether safety harnesses were required, if the mobile stairs were prematurely moved, or if there was a miscommunication between the ground crew and the personnel inside the cabin. The involvement of a third-party contractor also means that the investigation will likely scrutinize the coordination and safety oversight between Jet2 and its service providers at Manchester Airport.
The aviation industry maintains rigorous safety management systems to mitigate the risks associated with tarmac operations. Falls from height remain one of the leading causes of occupational injuries in aviation maintenance and ground handling. Regulatory bodies frequently collaborate on investigations of this nature to determine if workplace safety regulations were breached. The findings from Jet2’s internal investigation will likely be utilized to prevent future occurrences and ensure that third-party contractors adhere to stringent safety standards.
Frequently Asked Questions
When and where did the incident occur?
The fall took place at Manchester Airport at approximately 8:00 a.m. on Saturday, April 11, 2026.
Who was injured in the fall?
An unnamed male contractor, believed to be an aircraft engineer working for a third-party provider, sustained serious injuries including arm and leg fractures.
What airline was involved?
The incident involved a Jet2 aircraft that was scheduled to depart for Tenerife.
Sources
Photo Credit: X
Regulations & Safety
Saab Wins BULATSA Contract for I-ATS at Three Bulgarian Airports
Saab will deploy its latest I-ATS and A-SMGCS systems across Sofia, Varna, and Burgas airports to meet EU CP1 requirements.

Swedish defense and security company Saab has secured a contract with the Bulgarian Air Traffic Services Authority (BULATSA) to deploy its latest Integrated Air Traffic Control Suite (I-ATS) across three commercial airports in Bulgaria.
Announced in a press release on September 16, 2026, the agreement aims to modernize air traffic management at Sofia, Varna, and Burgas airports. The technology upgrade will ensure BULATSA operations comply with European Common Project One (CP1) requirements while providing tower and approach controllers with a scalable platform for future airspace demands.
Modernizing Bulgarian airspace infrastructure
BULATSA currently relies on Terminal Approach Radars at Sofia, Varna, and Burgas airports to manage controlled airspace. Sofia Airport already utilizes an earlier iteration of an Advanced Surface Movement Guidance and Control System (A-SMGCS), which was provided in part by Saab Technologies.
The newly signed contract will replace and upgrade these existing capabilities. Saab will deliver the latest version of I-ATS, which features an updated Human-Machine Interface (HMI) designed to improve controller situational awareness and workflow. Additionally, Sofia Airport will receive a completely new A-SMGCS installation to enhance surface movement tracking and ground safety.
Strengthening the Saab and BULATSA partnership
The deployment builds on existing relationships between the Swedish manufacturer and the Bulgarian air navigation service provider. Saab representatives indicated that the new systems will future-proof BULATSA operations as European airspace requirements evolve.
Cecilia Larsson, Head of Saab Air Traffic Management, highlighted the collaborative nature of the infrastructure upgrade.
“The agreement strengthens the long-standing partnership between Saab and BULATSA, reaffirming the shared commitment to delivering advanced air traffic management capabilities in Bulgaria. We look forward to the continued journey towards safe and efficient air traffic control.”
AirPro News analysis
We note that compliance with European Common Project One (CP1) is a primary driving factor for air navigation service providers across the continent right now. By upgrading to the latest I-ATS and A-SMGCS standards, BULATSA is aligning its infrastructure with broader Single European Sky ATM Research (SESAR) deployment goals. These mandates require the synchronized modernization of air traffic management systems to handle future capacity constraints and meet stringent environmental targets.
Sources: Saab AB
Photo Credit: Saab AB
Regulations & Safety
FAA Reports 24% Drop in Laser Strikes on Aircraft in 2026
The FAA recorded 4,470 laser strikes from January to July 2026, a 24% decline and the third straight year of falling incidents.

This is a developing story. Information may change as official details are released.
The Federal Aviation Administration (FAA) reported a 24 percent decrease in laser strikes on aircraft during the first seven months of 2026 compared to the same period last year. Despite the decline, the agency continues to highlight the severe safety risks and legal consequences associated with targeting aircraft in the National Airspace System.
Pilots reported 4,470 laser strikes between January and July 2026. The data, published by the FAA on September 17, 2026, marks the third consecutive year of declining incidents following an all-time high of 13,304 reported strikes in 2023. Laser strikes remain a critical safety hazard because high-powered beams can distract or temporarily blind flight crews during critical phases of flight.
Regional trends and pilot safety
The FAA data indicates that incidents remain concentrated in states with high volumes of air traffic. California recorded the highest number of occurrences, with 614 laser strikes reported from January through July 2026. Texas followed with 445 reported strikes, and Florida recorded 232 incidents during the same period.
The physical risk to flight crews remains a primary concern for regulators. Since the FAA began tracking laser strike data in 2010, pilots have reported 322 injuries resulting from laser exposure. The agency continues to coordinate with local law enforcement and the Federal Bureau of Investigation (FBI) to identify and prosecute offenders.
Federal enforcement and criminal penalties
Individuals who aim lasers at aircraft face severe civil and criminal penalties. The FAA can impose civil fines of up to $11,000 per violation. Under federal criminal law, offenders can face up to five years in prison and a maximum fine of $250,000.
The Department of Justice (DOJ) has actively pursued prison sentences for recent offenders. On July 10, 2026, a 31-year-old New York man was sentenced to 18 months in federal prison. The sentencing followed a March 2024 incident in which the man pointed a green laser at a Delta Air Lines (DL) flight on approach to Buffalo Niagara International Airport (BUF).
High-altitude targeting
While many laser strikes occur during approach and departure phases, high-powered commercial lasers are increasingly capable of reaching aircraft at cruising altitudes. On September 15, 2026, a Boeing 737 cruising at 34,000 feet over northern Wisconsin was targeted by a laser. Minneapolis air traffic control notified local authorities, though no suspect has been identified.
According to reporting by AVweb, ADS-B flight tracking data suggests the targeted aircraft may have been Air Canada (AC) Flight 1275, operated by a Boeing 737 MAX 8. Air Canada, the FAA, and local law enforcement have not publicly confirmed the specific flight involved in the Wisconsin incident.
AirPro News analysis
We note that while the 24 percent drop in laser strikes is a positive trend for the aviation industry, the raw numbers remain elevated compared to historical baselines before the 2023 peak. The September 15 incident over Wisconsin demonstrates the evolving nature of the threat. Lasers capable of reaching a Boeing 737 at 34,000 feet are easily accessible to the public, complicating enforcement efforts for local police and the FBI. The 18-month federal prison sentence handed down in July 2026 signals that the DOJ is willing to pursue substantial custodial sentences to deter future offenses, moving beyond the civil fines traditionally levied by the FAA.
Sources: Federal Aviation Administration, Department of Justice, AVweb
Photo Credit: FAA
Regulations & Safety
FAA Activates 100th Surface Awareness Initiative System
The FAA reaches a milestone in its 220-airport SAI deployment, using ADS-B data to improve runway safety and controller awareness.

The Federal Aviation Administration (FAA) has activated its 100th Surface Awareness Initiative (SAI) system, marking a halfway point in a nationwide deployment aimed at reducing runway incursions and improving air traffic controller situational awareness. U.S. Transportation Secretary Sean P. Duffy and FAA Administrator Bryan Bedford announced the milestone on September 2, 2026.
In a press release issued by the agency, officials confirmed that the SAI technology is now operational at 100 air traffic control towers. The system leverages Automatic Dependent Surveillance-Broadcast (ADS-B) data to provide controllers with real-time tracking of aircraft and ground vehicles. This capability is particularly critical during periods of low visibility or when portions of the airfield are outside the direct line of sight from the control tower.
Accelerated rollout of surface safety technology
The FAA plans to install the SAI system at a total of 220 airports that previously lacked surface surveillance capabilities. According to the agency, an additional 44 facilities are scheduled to receive the technology by the end of 2026. Recent installations include Ann Arbor Municipal Airport (ARB), Billings-Logan International Airport (BIL), Gulfport-Biloxi International Airport (GPT), Greenville-Spartanburg International Airport (GSP), and Corpus Christi International Airport (CRP).
The accelerated deployment is supported by a $12.5 billion allocation for air traffic control modernization under the Working Families Tax Cut Act.
“We have doubled our deployment speed thanks to Republicans in Congress who delivered funding through the Working Families Tax Cut Act,” Duffy stated. “We’re going to continue fast-tracking our deployment so that all 220 FAA towers that did not have surface surveillance capabilities can now have a new tool at their disposal for controllers.”
Broader air traffic control modernization
The SAI milestone is part of a wider initiative by the U.S. Department of Transportation (DOT) and the FAA to upgrade aging aviation infrastructure. FAA Administrator Bryan Bedford emphasized the operational necessity of the new systems.
“SAI is vital for controllers. It gives them the big picture of the airport’s surface right at their fingertips,” Bedford said. “For our controllers to work at their best, they need the technology to match their expertise.”
The September 2 announcement follows a series of related infrastructure investments. In late August 2026, the FAA highlighted a $27.3 million project to modernize the air traffic control system at Norfolk International Airport (ORF). Duffy and Bedford also recently inaugurated a $40 million Rohde & Schwarz USA manufacturing facility in Frederick, Maryland. The plant will produce digital Voice over IP switches for the national airspace system.
The agency has also continued deploying Surface Movement Radar Model 4 (SMR-4) systems, with recent installations completed at Ronald Reagan Washington National Airport (DCA) and Newark Liberty International Airport (EWR).
AirPro News analysis
The rapid deployment of the Surface Awareness Initiative represents a pragmatic approach to a persistent safety challenge. Historically, advanced surface surveillance systems were limited to the nation’s largest and busiest hub airports due to high installation and maintenance costs. By utilizing existing ADS-B out data, which is already mandated for most aircraft operating in controlled airspace, the FAA can provide smaller and mid-sized regional airports with a digital picture of the airfield at a fraction of the cost. We view this 100-tower milestone as a critical step in closing the technology gap between major international hubs and regional facilities, ultimately creating a more uniform safety standard across the national airspace system.
Sources: Federal Aviation Administration
Photo Credit: Federal Aviation Administration
-
UAV & Drones4 days agoJoby Aviation Completes First Autonomous US Transcontinental Flight
-
Space & Satellites6 days agoNASA Awards SpaceX Launch Contract for StarBurst Mission
-
UAV & Drones6 days agoPrismatic Wins £15.7M ARIA Contract for PHASA-35 Power Beaming
-
Space & Satellites3 days agoStoke Space Raises $1B Series E to Scale Nova Rocket Program
-
Space & Satellites20 hours agoSpaceX Starship Flight 14 Targets First Orbital Mission
