Connect with us

Regulations & Safety

TSB Reports Fatal 2023 Helicopter Accident During Maintenance Run

TSB Canada details a fatal 2023 helicopter accident at Smithers Airport caused by skipped checklists and pilot distraction. Mustang Helicopters updates safety policies.

Published

on

This article is based on an official press release from the Transportation Safety Board of Canada.

On May 27, 2026, the Transportation Safety Board of Canada (TSB) released its final investigation report (A23P0040) detailing the circumstances surrounding a fatal incident that occurred three years prior. The incident, which took place on May 6, 2023, at Smithers Airport (CYYD) in British Columbia, involved an Airbus Helicopters AS 350 B3 operated by Mustang Helicopters Inc.

According to the official TSB press release and accompanying report, the accident occurred during a maintenance ground run, resulting in the death of one ground worker and serious injuries to another. The investigation highlights critical safety issues, specifically the severe dangers of procedural complacency and digital distraction in the cockpit during ground operations.

The Incident at Smithers Airport

Maintenance Ground Run Turns Fatal

The TSB report outlines that on the day of the accident, the Airbus AS 350 B3 helicopter (registration C-GUXR) was undergoing maintenance ground run operations. The specific procedure was designed to balance the tail rotor drive shaft, a highly technical task that requires the helicopter’s rotor system to be operated at nearly full RPM.

During the third maintenance ground run of the day, the aircraft suddenly entered an uncommanded and rapid rotation. At the time, two maintenance staff members were positioned on the ground near the helicopter’s left cargo door to monitor the balancing equipment. As the helicopter spun out of control, both workers attempted to evade the aircraft but were struck multiple times by the tail rotor. Tragically, one worker was fatally injured at the scene, while the other sustained serious injuries and was airlifted to a local hospital.

The TSB investigation notes that the pilot eventually managed to move the engine control to IDLE, shut off the fuel supply, and apply the rotor brake. The helicopter came to a rest after rotating approximately 540 degrees. The aircraft remained upright throughout the event, and no post-impact fire occurred.

Investigation Findings and Human Factors

Skipped Checklists and Unseen Hazards

In its analysis of the events leading up to the uncommanded rotation, the TSB identified several critical human factors and procedural deviations. Following the first maintenance run of the day, the pilot abbreviated the operator’s official checklist to expedite the process.

The pilot abbreviated the operator’s official checklist to expedite the process, viewing the task as “routine and repetitive.”

According to the TSB, this deviation meant that crucial safety steps were missed. Specifically, pressure was left in the hydraulic system, and the right anti-torque pedal remained engaged in a fully forward position. Because the checklist was skipped, this critical hazard went completely undetected prior to the third engine start.

The Role of Digital Distraction

A central finding of the TSB report is the role of digital distraction in the cockpit. Investigators found that the pilot’s attention was split between the highly sensitive maintenance operation and a cellphone, which was connected to a Bluetooth earpiece.

Because the pilot was looking down when the rapid rotation began, he was not expecting the sudden movement. The TSB concluded that his delayed response to the rotational yaw force was insufficient to stop the helicopter from spinning quickly. Investigators emphasized that the minimal time saved by skipping the official checklist was negligible and ultimately contributed to the fatal outcome.

Industry Implications and Safety Actions

Regulatory Blind Spots

The TSB report highlights a significant regulatory gap within the Canadian aviation framework. Currently, there are no Transport Canada regulations that explicitly prohibit the use of cellphones or personal electronic devices in the cockpit during operations.

The safety board has previously identified the severe risks associated with cellphone use in aviation accidents, noting that electronic devices can fatally divert a pilot’s attention from activities necessary for safe operations. The TSB presents this incident as a grim case study on the dangers of complacency during ground operations, which are often falsely perceived by crews as lower-risk than active flight.

Operator Corrective Measures

Following the tragic occurrence, Mustang Helicopters Inc. implemented several corrective safety measures aimed at preventing future incidents. According to the TSB report, the company introduced a strict new distraction policy that explicitly requires the stowing of all electronic devices during operations.

Additionally, Mustang Helicopters added a new standard operating procedure (SOP) specifically tailored for maintenance ground runs to its operations manual. The company also thoroughly revised and strengthened its hazard assessments and safety briefings for both maintenance personnel and pilots.

AirPro News analysis

We note that this tragic event underscores a critical vulnerability in modern aviation operations: the intrusion of personal electronics into safety-critical environments. While active flight operations often command a pilot’s full attention, ground operations, such as maintenance runs, can falsely appear lower-risk, inviting a dangerous level of complacency. The TSB’s findings suggest that regulatory bodies like Transport Canada may need to urgently modernize their frameworks to explicitly address digital distractions. Ensuring that the cockpit remains a sterile, focused environment, even when the aircraft is firmly on the ground, is paramount to preventing similar tragedies in the future.

Frequently Asked Questions (FAQ)

What caused the helicopter to spin during the maintenance run?

According to the TSB, the pilot skipped portions of the checklist, leaving hydraulic pressure in the system and the right anti-torque pedal in a fully forward position. When the engine was started for the third run, this caused an uncommanded and rapid rotation of the aircraft.

Why didn’t the pilot stop the rotation immediately?

The TSB investigation found that the pilot was distracted by a cellphone connected to a Bluetooth earpiece and was looking down when the rotation began. This distraction led to a delayed and insufficient reaction to the sudden yaw force.

Are pilots allowed to use cellphones in the cockpit in Canada?

The TSB report highlights that there are currently no Transport Canada regulations explicitly prohibiting the use of cellphones or personal electronic devices in the cockpit during operations, identifying this as a significant regulatory blind spot.

Sources

Photo Credit: TSB

Continue Reading
Click to comment

Leave a Reply

Regulations & Safety

NTSB Releases Preliminary Report on Carlisle Airport Midair Collision

NTSB preliminary report details a fatal midair collision between a Cessna 150H and a PA State Police helicopter at Carlisle Airport.

Published

on

This is a developing story. Information may change as official details are released.

This is original reporting and analysis by AirPro News.

The National Transportation Safety Board (NTSB) has released its preliminary report on an August 19, 2026, midair collision at Carlisle Airports (N94) in Pennsylvania that resulted in the death of a civilian pilot and injuries to two state troopers. The collision involved a Cessna 150H and a hovering Pennsylvania State Police (PSP) Bell 407GX Helicopters during mixed-aircraft operations at the non-towered airfield.

Released on September 2, 2026, the preliminary investigation record outlines the sequence of events leading up to the 6:52 p.m. local time collision. The NTSB report confirms that both aircraft were in communication via the Common Traffic Advisory Frequency (CTAF) prior to the event. The exact cause of the collision remains under Investigation by the NTSB and the Federal Aviation Administration (FAA).

Flight path and collision sequence

According to the NTSB preliminary report and statements from the PSP, the Bell 407GX helicopter was conducting a training exercise. The helicopter crossed the runway threshold at an altitude of 50 feet before descending into a hover taxi. At the same time, the Cessna 150H was approaching the airport to land.

Radio communications detailed in the report indicate that the helicopter crew instructed the Cessna pilot to extend his downwind leg. The Cessna pilot acknowledged the instruction, stating his intention to land after the helicopter. However, as the helicopter hovered off the runway, the Cessna veered off its intended landing path to the north side of the runway. The fixed-wing aircraft subsequently collided with the rear of the hovering helicopter, striking its tail and main rotors.

Casualties and ongoing investigation

The collision resulted in one confirmed fatality. The pilot of the Cessna 150H, identified by his employer Penn State Health as 57-year-old Dr. Paul William Sokoloski, sustained fatal injuries. The two occupants of the PSP helicopter, identified as Corporal Bryce Corman and Trooper Jason Mills, sustained injuries in the collision.

NTSB aviation Accident investigator Aaron McCarter is leading the inquiry. While surveillance video captured the collision, the NTSB has not yet determined why the Cessna deviated from its landing path. A final report detailing the probable cause is not expected for several months.

AirPro News analysis

We note that mixed-aircraft operations at non-towered airports inherently require precise communication and situational awareness, particularly when fixed-wing aircraft and rotorcraft share the same traffic pattern. While some aviation commentators have speculated that rotor wash or wake turbulence from the hovering Bell 407GX may have contributed to the Cessna 150H veering off course, this remains entirely unverified. The NTSB has explicitly stated that it is too early to attribute the Cessna’s flight path deviation to any specific factor. Investigators will likely examine environmental conditions, aircraft performance data, and pilot actions as they work toward a final probable cause determination.

Sources: National Transportation Safety Board

Photo Credit: NTSB

Continue Reading

Regulations & Safety

NTSB: Thermal Plugs Caused AA Flight 3023 Tire Failure

NTSB determines melted thermal relief plugs caused tire failure on American Airlines 737-8 at Denver, triggering emergency evacuation.

Published

on

The National Transportation Safety Board (NTSB) has determined that melted thermal relief plugs caused the left main landing gear tires to fail on an American Airlines Boeing 737-8 during a July 2025 takeoff roll at Denver International Airport (DEN), prompting a high-speed rejected takeoff and emergency evacuation.

The final aviation investigation report, published on August 26, 2026, officially closes the inquiry into American Airlines Flight 3023. The document details the mechanical sequence that led to the tire failure while highlighting significant passenger noncompliance during the subsequent evacuation, as travelers ignored crew commands and retrieved carry-on baggage.

Mechanical sequence and rejected takeoff

The incident occurred on July 26, 2025, involving a Boeing 737-8, registration N306SW, equipped with CFM International LEAP-1B28 engines. According to the NTSB, the flight experienced an approximate 25-minute delay while awaiting departure at runway 34L.

During the subsequent takeoff roll, as the aircraft reached an indicated airspeed between 90 and 100 knots, the captain reported hearing a loud pop accompanied by a noticeable bump. The flight crew initiated a rejected takeoff at speeds above 80 knots.

The NTSB determined the probable cause of the incident was the melting of thermal relief plugs in the left main landing gear. This melting released tire pressure and caused the tires and wheels to fail during the takeoff roll. The agency noted that this failure resulted in abnormal airplane handling characteristics, which prompted the flight crew to reject the takeoff. Debris from the fractured wheels caused minor damage to the aircraft, including a three-inch dent on the lower skin of the left wing.

Emergency evacuation and passenger behavior

Following the rejected takeoff, the flight crew initially instructed the cabin to remain seated. Between 30 and 45 seconds later, after identifying smoke and fire originating from the left main landing gear, the crew ordered an emergency evacuation.

The aircraft carried 175 occupants, comprising 169 passengers and six crew members. The NTSB final report confirms that zero injuries occurred during the event. This official casualty figure supersedes preliminary media reports from July 2025 that had indicated minor injuries and hospital evaluations.

The investigation report draws specific attention to passenger behavior during the emergency egress. The NTSB stated that the cabin crew described the evacuation as rapid but hindered by significant passenger confusion and noncompliance. Despite flight attendants repeatedly commanding passengers to leave their belongings behind, multiple individuals retrieved their carry-on baggage. The NTSB concluded that this noncompliance directly slowed the flow of egress from the aircraft.

AirPro News analysis

The NTSB findings regarding American Airlines Flight 3023 add to a well-documented and growing safety concern within the commercial aviation sector. Passenger retrieval of carry-on baggage during emergency evacuations is a recurring issue that compromises the 90-second evacuation standard mandated by the Federal Aviation Administration (FAA).

When passengers stop to open overhead bins and carry luggage down escape slides, they not only slow the egress rate for those behind them but also introduce the risk of puncturing the evacuation slides or injuring fellow passengers. We continue to see official accident reports cite passenger noncompliance as a negative factor in evacuation efficiency. This recurring behavioral pattern has prompted safety advocates and lawmakers to question whether current FAA evacuation certification tests, which rely on compliant participants, accurately reflect real-world human behavior during an emergency.

Sources: National Transportation Safety Board

Photo Credit: National Transportation Safety Board

Continue Reading

Regulations & Safety

Marine One Loss of Separation at DCA: NTSB Preliminary Report

NTSB cites radio line-of-sight failure after Marine One and Envoy Air E-170 came within 0.82 NM at Reagan National.

Published

on

This is a developing story. Information may change as official details are released.

This is original reporting and analysis by AirPro News.

A loss of separation occurred on August 4, 2026, between a Sikorsky VH-3D operating as Marine One and an Envoy Air Embraer E-170 departing Ronald Reagan Washington National Airport (DCA). The incident took place approximately two miles north of the airport at 14:34 EDT and prompted an immediate Federal Aviation Administration (FAA) relocation of radio equipment after investigators identified a communication failure.

According to a preliminary report released on August 27, 2026, by the National Transportation Safety Board (NTSB), air traffic controllers at DCA did not receive a required three-minute pre-departure warning from the helicopter. The event triggered a review of strict Safety protocols implemented following a fatal midair collision in the same airspace in January 2025.

Incident timeline and separation data

The loss of separation occurred when Marine One departed The Ellipse simultaneously with Envoy Air flight 3742 departing runway 1 at DCA. Preliminary FAA estimates indicate the aircraft came within 0.82 nautical miles (NM) laterally and 700 feet vertically. The NTSB is currently analyzing surveillance data to establish the exact closest point of approach.

President Donald Trump was on board the Sikorsky VH-3D at the time of the incident. In a statement provided to CBS News, White House spokesman Kush Desai confirmed the President was never in danger.

Marine One flights are piloted by the finest aviators in the world, and the White House maintains the utmost confidence in these patriots and other security officials who are responsible for ensuring the President’s safety.

No injuries were reported among the occupants of either aircraft, and both flights continued to their respective destinations without further incident.

Communication failure and FAA response

The NTSB preliminary report points to inadequate radio line-of-sight coverage between The Ellipse and the DCA tower as the primary factor in the missed pre-departure warning. A DCA tower controller reported that the transmission attempt from the helicopter was “broken and unreadable,” according to CBS News.

Following the August 4 incident, FAA technicians evaluated the infrastructure and confirmed the line-of-sight deficiency. To resolve the issue, the agency relocated the helicopter-control radio equipment to the top of the DCA control tower. Subsequent communication checks were successful.

CBS News also reported that recent construction at the White House may have contributed to the radio line-of-sight degradation, though the NTSB has not yet issued a final determination on the cause.

Regulatory context and prior airspace changes

The airspace surrounding DCA operates under highly specific procedural rules designed to deconflict fixed-wing airline traffic from frequent VIP helicopter movements. These procedures were significantly tightened following a fatal midair collision on January 29, 2025, involving an airliner and an Army Black Hawk helicopter near the airport.

Following the 2025 accident, regulators instituted a requirement for a ground stop at DCA anytime a Helicopters passes on a conflicting route. The failure of the three-minute warning on August 4 prevented controllers from initiating this required ground stop for the Envoy Air departure.

Air traffic controllers and Marine One pilots had previously met on July 28, 2026, exactly one week prior to the incident, to discuss ongoing communication challenges in the sector.

AirPro News analysis

The August 4 loss of separation highlights the fragility of procedural deconfliction in the Washington, D.C. airspace. While the FAA characterized the event as a momentary loss of separation, the failure of a critical communication link reveals a single point of failure in the safety protocols established after the 2025 collision. We note that the rapid relocation of the radio equipment by the FAA demonstrates an acknowledgment of the infrastructure gap. As the NTSB continues its Investigation, we will monitor the docket for potential systemic recommendations regarding how VIP helicopter movements integrate with high-volume Commercial-Aircraft traffic at DCA, particularly concerning redundant communication systems.

Sources: National Transportation Safety Board

Photo Credit: National Transportation Safety Board

Continue Reading
Every coffee directly supports the work behind the headlines.

Support AirPro News!

Advertisement

Follow Us

newsletter

Latest

Categories

Tags

Every coffee directly supports the work behind the headlines.

Support AirPro News!

Popular News